How to use Fgtech Galletto v54 for Bosch MG7.9.8
This is an excellent write-up of how to use Fgtech 4 Galletto v54 to successfully read Bosch MG 7.9.8safely and quickly without desolder resistor, on Kia cars or Hyundai with automatic transmission.
This ECU is installed on Kia cars, Hyundai with automatic transmission. Operation with this computer is carried out using the bookmark M7.9.8.ECU is based on a 16-bit processor ST10F275.
MARKING AND INTERCHANGEABILITY BY:
The full alphanumeric code of the marking contains in itself enough
A large set of characters and looks something like this:
PM98D442E / DGFD_836CFS2_5000, where
PM98D442E – Software ID (Software ID)
DGFD_836CFS2_5000 – Hardware ID (Calibration ID)
Explanation:
PM95D442E \ DGFD_836CFS2_5000
The software PM95D442E says that the P / O from the motor processor
BOSH M7.9.8 and installed software D442E.
ATTENTION!
ALL firmware COMPATIBLE only Within one software
Calibrations of DGFD_836CFS2_5000 mean the following
D – cars
G – Gasoline engine (Gazoline)
FD – HYUNDAI _i30
May be:
– AM – KIA_Soul
– LD – KIA_Cerato
– TD – KIA_Cerato
– ED – KIA_Ceed
– JB – KIA_Rio
– MC – Hyundai_Accent, Verna
– HD – Hyundai_Elantra
– PB – Hyundai_i20
– PA – Hyundai_i10
5 – ECU Manufacturer
3 – Toxicity standards according to the European standard (3-E3, A-E3, 4-E4, H-E4)
6 – Engine capacity (4 – 1.4 liters, 6 – 1.6 liters)
CFS- Complete set (including presence-absence of IMMO survey)
– With (D) ES MT Immo Off
– With (D) FS MT Immo
– With (D) PS AT Immo Off
– C (D) QS AT Immo
Where is the first “C” marking for HYUNDAI vehicles
“D” marking for KIA vehicles
2_5000 – version of software calibrations
On vehicles with automatic transmission under the marking of the engine block software
Marking of the software of the processor of the automatic transmission.
For example: THD2C16UB2
T – means that this software refers to the transmission processor (transmission)
HD – Hyundai_Elantra
2C – indicates the gear ratio of GP
16 – the volume of the engine with which the transmission operates in pairs
UB2 – software version
The ECU supports the programming modes:
Connect
Attention! All programming commands must be executed from the computer, which is translated in the reprogramming mode, except for the “Establish communication” mode, which is used to transfer the unit from the diagnostic mode to the reprogramming mode.
This block supports read / write commands for FLASH memory of the Bosch MG 7.9.8 computer only in “on the desk” mode when the computer is in programming mode (or the so-called “boot mode”).
The correct size of FLASH firmware for Bosch ECU computer is 7.9.8 – 832 KB (851968 bytes).
11 Switching voltage
Left connector:
12 CAN-H (connected via J2534 device)
27 CAN-L (connected via J2534 device)
56 Non-disconnecting voltage
59 K-line (motor)
Right connector:
2 ECU mass
6 Power supply after main relay (not used)
84 K-line (automatic transmission)
To transfer the computer to the programming mode, it must be modified. For finalization, it is necessary to disassemble the computer and connect three red and three blue contacts on the board (shown in the figure below). White color indicates unused contacts for better orientation.
( Fg Galletto v54 read MG7.9.8 without desolder resistor, with this two connections)
Then you need to connect to the computer in accordance with the connection diagram below. Then you can perform operations with the computer.
for car with automatic transmission:
connector A (small) 11, 56 = +12v
59 = K-Line
connector B (large) 1,2,3 = computer weight
(just connect any of the indicated contacts)
84 = K-Line, automatic transmission
Note: The corresponding K-Line must be connected depending on what operations are to be performed (with the automatic transmission or the engine).
for car with manual transmission:
solder 1k resistor instead of 100 ohm
you need two 12+
82= 12+
83= 12+
85= K-Line
2= Ground
ATTENTION!
To avoid problems with “falling asleep”, the computer must be filled in the unit
Modified software calibrated on the basis of “native” software, i.e.
Software ID type for example: PM98C441C (or M98C441C) in native and
Modified firmware should, if possible, be the same.
All flash players allow you to determine the ID of the Basic software of a specific ECU.
It looks something like this:
Credits to:
http://chiptung.narod.ru/Bosch_MG_7_9_8.html
http://chiptuner.ru/content/bsl_mg798/
http://www.digital-kaos.co.uk/forums/showthread.php/457340-me7-9-8-mg7-9-8/
NO ONE BUT YOURSELF ARE RESPONSIBLE OF WHAT YOU’LL TRY.
GOOD LUCK.
