Shipping From UK
Home - Products - Technical Service - VCM 2 technical support and error solution
« Go Back

VCM 2 technical support and error solution

Matched Product
VCM2 for V145 LandRover & Jaguar and V97 MAZDA 2 in 1 Quality A

VCM2 for V145 LandRover & Jaguar and V97 MAZDA 2 in 1 Quality A   Item No. SP177-E

Latest price:€219.00 Buy It Now:€169.00 23% off       Click Here to Shop
Professional LandRover & Jaguar and MAZDA scanner. Basic function including diagnose, module programming, read/clear DTC, key programming and so on.

Description

Q: When i connect VCM2 with my car and laptop, the light will be on, after 4-5 minutes, all the light on main unit is off. I disconnect the connection with laptop and car. Then connect the VCM2 with laptop and car again, all light will be on as usual. What should i do?

A: See the following photo. Go to your local shop to buy this capacitance, or contact us we will resend the new one to replace.

vcm 2 ii diagnostic

VCM 2 unit is housed in a shock resistant polycarbonate case with rubber end boots, along with an extended operating temperature and voltage range, for increased durability and ruggedness in service bay and road test environments,
 
BUT do ensure the VCM II is not subjected to extreme temperature or prolonged exposure to direct sunlight that may cause heating of the VCM II.
 
Environmental requirement: Temperature & Humidity
Operating:
VCM II unit: -20ºC to 70ºC (-4ºF to 158ºF)
Wireless USB 2.0 adapter: 0ºC to 50ºC (32ºF to 122ºF) at 10% to 90% RH non-condensing
 
Storage: -40ºC to 85ºC (-40ºF to 185ºF) at 10% to 90% RH non-condensing
 
 
Issues & Causes/Solutions: VCM 2 & Temperature
 
Issue:
VCM II turns off (shutsdown/suspends-operation, all LEDs off) immediately after being powered by the USB cable or DLC cable
 
Cause/Solution:
• Verify the ambient temperature is within the acceptable operating range for the VCM II device: -20°C to 70°C (-4°F to 158°F)
• If the ambient temperature is outside this range allow the temperature to return to the acceptable operating range and the VCM II will automatically resume operation
• If VCM II error persists when the ambient temperature returns to its operating range, contact your regional technical support
 
Issue:
VCM II does not appear in the list of detected wireless devices in IDS and  its Power LED blinks at a periodic rate
 
Cause/Solution:
• Verify the VCM II is connected to the DLC cable and the DLC cable is connected to the vehicle. The VCM II must be powered using the DLC cable for the wireless interface to be operational
• Verify the ambient temperature is within the acceptable operating range for the VCM II's wireless interface: 0°C to 50°C (32°F to 122°F)
• If the ambient temperature is outside this range allow the temperature to return to the acceptable operating range and the VCM II's wireless interface will automatically be  enabled and the Power LED will stop blinking and stay illuminated
• If VCM II wireless interface problem persists when the ambient temperature returns to its operating range, contact your regional technical support
 
Issue:
VCM II's Power LED blinks continuously after being powered using the DLC cable
 
Cause/Solution:
• Verify the ambient temperature is within the acceptable operating range for the VCM II's wireless interface: 0°C to 50°C (32°F to 122°F)
• If the ambient temperature is outside this range allow the temperature to return to the acceptable operating range and the VCM II's wireless interface will automatically be enabled and the Power LED will stop blinking and stay illuminated
• If VCM II wireless interface problem persists when the ambient temperature returns to its operating range, contact your regional technical support or ask obdexpress.co.uk for help/
 
Write a Review
* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Detail:
*Verification Code:
      7738    No right? Get a new Verification Code
 
Share your thoughts about this item with other users. All reviews will be reviewed within two working days, aggressive reviews and spam will be blocked.
After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).
Please Sign In first if you want to later edit or manage reviews uploaded by yourself.

Search

You can search Technical Service by keyword.