OBDSTAR X300 DP Plus programming proximity key: For 2019 Nissan Sylphy (B18)


2019 Nissan Sylphy (B18) proximity key is programmed by OBDSTAR X300 DP Plus (Key Master DP Plus) and OBDSTAR NISSAN-40 BCM Cable via OBD. No need pincode, no risk!

 

What is OBDSTAR NISSAN-40 BCM Cable?

NISSAN-40 BCM Cable is a professional harness for Nissan proximity key adding and all key lost. With this cable, there is no need to break or hook up the wires and no risk of damaging the communication cables!

OBDSTAR X300 DP Plus programming Nissan proximity key

  • Support proximity key adding (no need pincode)

(The model can replace the Nissan/Renault 16+32 cable)

Nissan Sentra

 

  • Support proximity key adding and all key lost (no need pincode)

Nissan Rogue T33

Nissan Pathfinder

Mitsubishi Outlander 2021

 

How to add smart key?

Remove the trim panel under the dashboard and locate the BCM module

Use Nissan-40 BCM cable to connect the BCM module, and connect with X300 DP Plus main cable

OBDSTAR X300 DP Plus programming Nissan proximity key
 

Enter the "DP" interface and accept the disclaimer

Select CAR IMMO>> All>> NISSAN INFINITI>> NISSAN INFINITI V32.39 (newest version)>> Manual Select System>> 28 Digital PinCode>> SYLPHY (B18)/SENTRA>> PROXIMITY>> 2019->> Add Keys (Free PinCode)

OBDSTAR X300 DP Plus programming Nissan proximity key
OBDSTAR X300 DP Plus programming Nissan proximity key
OBDSTAR X300 DP Plus programming Nissan proximity key
OBDSTAR X300 DP Plus programming Nissan proximity key
 

Make sure the internet connection is normal before operation.

Pay attention to the warning, and follow the prompts to operate:

This function continues to need to unplug the gateway interface, and then use the dedicated Nissan/Renault 16+32 interface to connect to the unplugged gateway interface. Continue or not?

Click "Enter"

OBDSTAR X300 DP Plus programming Nissan proximity key
 

Note:

1. Executing this function will clear all the keys of the vehicle. The deleted keys must be re-programmed before they can be used normally;

2. Only 2 new keys can be programmed each time. If you need to program more than 3 keys, please divide them into two operations;

3. There must be at least one key that can start the vehicle normally;

4. After the 4-button smart key programming is completed, if the transponder and the smart are not normal, please try write HFM config.

 

Warning:

1. To ensure that the Pincode is successfully read, please turn on the ignition switch;

2. The device must not be disconnected during the Pincode reading process, otherwise the module will be damaged;

3. Please check the vehicle voltage, line connection, and other conditions to prevent the device from connecting abnormally in the middle.

 

Writing data…wait for 5 minutes

Reading data…

The current 28-digit Pincode for the vehicle is 395ADC00F112Fxxx.

This Pincode can be used when all the keys of the current vehicle are lost to perform key programming operation.

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Turn on the double flash, turn off the ignition switch

Switch igniton on

 

Long press the start button to turn off the ignition switch;

Turn on the hazard warning lights (double flashing lights)

The gear position is in P gear or neutral gear;

The steering column lock is in the unlock state.

 

Start to read the key ID:

Place the 1st smart key to be programmed (with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.

Special note:

1. Do not move the key on the ignition switch;

2. Do not press any button of the smart key;

3. Do not insert or remove the blade key in the smart key.

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Read the new key number is 0, old key number, and current total key number are 1

Note:

Here you need to read all key IDs to be programmed;

New keys can only be programmed at most 2 keys, the total number of keys is up to 4;

Click Esc to enter the next step

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Start programming the key:

Place the 1st smart key to be programmed (with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.

Special note:

1. Do not move the key on the ignition switch;

2. Do not press any button of the smart key;

3. Do not insert or remove the blade key in the smart key.

The key is being programmed. Do not move the key…

Program key successfully, click Esc to the next step

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Now the number of keys successfully programmed is 1.

Follow the following operations to complete the programming function:

1. Turn off the hazard warning lights (double flashing lights);

2. Press the lock and unlock buttons of each smart key one by one to verify whether it is normal;

3. Check one by one whether each smart key can be put into the car to start the car;

4. After completing the above operations, click Enter to end the function.

OBDSTAR X300 DP Plus programming Nissan proximity key

 

After all keys have been verified, please do not exit this function, and click Enter to continue after completing the operation according to the following prompts:

1. Remove the dedicated Nissan/Renault 16+32 connector and restore the gateway module;

2. Connect the OBDSTAR Device to the vehicle OBDII connector and turn on the ignition switch

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Clearing fault code…

Program success

OBDSTAR X300 DP Plus programming Nissan proximity key

 

Alright! 2019 Nissan Sylphy (B18) proximity key is programmed perfectly by OBDSTAR X300 DP Plus key programmer and NISSAN-40 BCM Cable by OBD.

 

www.obdexpress.co.uk